Model 682A03 Product Type: 4-20 mA Transmitter, DIN Rail, Vibration Transmitter DIN rail mount vibration transmitter (for use w/ICP® sensor), 4 to 20 mA output, 3 to 10k Hz View Spec Sheet (PDF) View photo and drawing .
PERFORMANCE ENGLISH SI Channels 1 1 Input Signal(Vibration) ± 100 mV/g ± 10.2 mV/(m/s²) [2] Input Signal(Temperature) 0 to 1.2 VDC 0 to 1.2 VDC [3] Output Signal(DC Vibration) 4 to 20 mA 4 to 20 mA [4] Output Signal(DC Vibration) 0 to 5 VDC 0 to 5 VDC [1][5] Output Signal(DC Vibration) 0 to 10 VDC 0 to 10 VDC [1][5] Output Signal(Temperature) 4 to 20 mA 4 to 20 mA [3] Output Signal(± 0.01 %)(AC Vibration) 100 mV/g 10.2 mV/(m/s²) [6] Frequency Range(-3 dB)(Acceleration) 180 to 600,000 cpm 3 to 10k Hz [7][8][9] Frequency Range(-3 dB)(Velocity) 210 to 600,000 cpm 3.5 to 10k Hz [7][8][9] Frequency Range(-3 dB)(Displacement) 210 to 60,000 kHz 3.5 to 1000 Hz [7][10][8] Output Range(DC Acceleration) 0 to 5.00 g pk or rms 0 to 49.03 m/s2 pk or rms [1][11][2] Output Range(DC Acceleration) 0 to 10.00 g pk or rms 0 to 98.06 m/s2 pk or rms [1][11][2] Output Range(DC Acceleration) 0 to 20.00 g pk or rms 0 to 196.12 m/s2 pk or rms [1][11][2] Output Range(DC Velocity) 0 to 0.5 in/sec pk or rms 0 to 12.7 mm/s pk or rms [1][11][2] Output Range(DC Velocity) 0 to 1.00 in/sec pk or rms 0 to 25.4 mm/s pk or rms [1][11][2] Output Range(DC Velocity) 0 to 2.00 in/sec pk or rms 0 to 50.8 mm/s pk or rms [1][11][2] Output Range(DC Displacement) 0 to 25.0 mil pk - pk 0 to 0.635 mm pk - pk [1][11][2] Output Range(DC Displacement) 0 to 50.0 mil pk - pk 0 to 1.27 mm pk - pk [1][11][2] Output Range(DC Displacement) 0 to 100.0 mil pk - pk 0 to 2.54 mm pk - pk [1][11][2] ENVIRONMENTAL Temperature Range(Operating) 32 to 158 °F 0 to 70 °C Temperature Range(Storage) -40 to 257 °F -40 to 125 °C Humidity Range(Non-Condensing) 0 to 95 % 0 to 95 % ELECTRICAL Power Required DC power DC power DC Power 18 to 36 VDC 18 to 36 VDC DC Power(maximum) 125 mA 125 mA Settling Time <2 min <2 min Load Resistance(4-20 mA, maximum) 500 ohm 500 ohm Load Resistance(0-5/10 V, minimum) 1000 ohm 1000 ohm Electrical Isolation(input/output) 500 VDC 500 VDC Excitation Voltage(delivered to sensor) 23 to 25 VDC 23 to 25 VDC Constant Current Excitation(delivered to sensor) 3 to 5 mA 3 to 5 mA Zero Measurand Output(± 2% of Span)(DC Vibration Current Output) 4 mA 4 mA Output Span(± 5.0 %)(DC Vibration Current Output) 16 mA 16 mA Zero Measurand Output(± 2% of Span)(DC Vibration Voltage Output) 0 VDC 0 VDC Output Span(± 5.0 %)(DC Vibration Voltage Output) 5 or 10 VDC 5 or 10 VDC [1] Zero Measurand Output(± 2% of Span)(Temperature Current Output) 4 mA 4 mA Output Span(± 5.0 %)(Temperature Output) 16 mA 16 mA PHYSICAL Electrical Connector(input/output) Removable Screw Terminals Removable Screw Terminals Electrical Connector(raw vibration output) BNC Jack BNC Jack Housing Material Polyamide Polyamide Size (Height x Width x Depth) 3.9 in x 0.9 in x 4.5 in 99 mm x 22.5 mm x 114.5 mm Weight(Maximum) 6.4 oz 127 Screw Terminal Wire Size 24-14 AWG 24-14 AWG Din Rail Mount 1.38 in 35 mm Status Indicator(Power "on") Green LED Green LED Status Indicator(Input Fault) Red LED Red LED Status Indicator(Measurement Mode - Acceleration) Green LED Green LED Status Indicator(Measurement Mode - Velocity) Green LED Green LED Status Indicator(Measurement Mode - Displacement) Green LED Green LED All specifications are at room temperature unless otherwise specified. NOTES: [1] Internal Dip switch selectable [2] Output measurement range is based upon input from 100 mV/g ICP® accelerometer and will be scaled inversely proportional to any percentage deviation of this input. [3] Requires use of accelerometer with "TO" temperature output option. [4] Output current voltage will fluctuate at frequencies below 5 Hz. [5] Factory set, 0-5 VDC. [6] Achieved with 100 mV/g ICP® accelerometer input. [7] Attenuation is -40 dB/decade. [8] The low frequency tolerance is accurate within ± 0.5 Hz of the specified frequency. [9] The high frequency tolerance is accurate within ± 0.5 kHz of the specified frequency. [10] Maximum 1,000 Hz for displacement. [11] Factory set, 1 in/sec peak. [12] See PCB Declaration of Conformance PS051 for details. [12]
Download Drawing 16165-NR.pdf
Top