Model 607A61 Product Type: Accelerometer, Vibration Sensor Low profile industrial ICP® accel, 100 mV/g, 0.5 to 10k Hz, side exit, 10-ft armored jacketed cable & swiveler base View Spec Sheet (PDF) View photo and drawing .
PERFORMANCE ENGLISH SI Sensitivity(± 15 %) 100 mV/g 10.2 mV/(m/s²) [2] Measurement Range ± 50 g ± 490 m/s² Frequency Range(± 3 dB) 30 to 600,000 cpm 0.5 to 10,000 Hz Resonant Frequency 1500 kcpm 25 kHz [1] Broadband Resolution(1 to 10,000 Hz) 350 µg 3434 µm/sec2 [1] Non-Linearity ± 1 % ± 1 % [3] Transverse Sensitivity ≤ 7 % ≤ 7 % ENVIRONMENTAL Overload Limit(Shock) 5000 g pk 49,050 m/s² pk Temperature Range -65 to +250 °F -54 to +121 °C Temperature Response See Graph See Graph [1] Enclosure Rating IP67 IP67 ELECTRICAL Settling Time(within 1% of bias) ≤ 2 sec ≤ 2 sec Discharge Time Constant ≥ 0.3 sec ≥ 0.3 sec Excitation Voltage 18 to 28 VDC 18 to 28 VDC Constant Current Excitation 2 to 20 mA 2 to 20 mA Output Impedance <150 ohm <150 ohm Output Bias Voltage 8 to 12 VDC 8 to 12 VDC Spectral Noise(10 Hz) 8 µg/√Hz 78.5 (µm/sec2)/√Hz [1] Spectral Noise(100 Hz) 5 µg/√Hz 49.1 (µm/sec2)/√Hz [1] Spectral Noise(1 kHz) 4 µg/√Hz 39.2 (µm/sec2)/√Hz [1] Electrical Isolation(Case) >108 ohm >108 ohm PHYSICAL Size (Hex x Height) 9/16 in x 1.0 in 14 mm x 25.4 mm Weight(without cable) 1.1 oz 31 gm [4] Mounting Stud Stud Mounting Thread 1/4-28 Male Not Applicable [5] Mounting Torque(stud) 7 to 8 ft-lb 9.5 to 10.8 N-m [6][7] Mounting Torque(hex nut) 2 to 5 ft-lb 2.7 to 6.8 N-m Sensing Element Ceramic Ceramic Sensing Geometry Shear Shear Housing Material Stainless Steel Stainless Steel Sealing Welded Hermetic Welded Hermetic Electrical Connector Integral Armored Cable Integral Armored Cable Electrical Connection Position Side Side Cable Length 10 ft 3.0 m Cable Type Polyurethane Polyurethane [8] SUPPLIED ACCESSORIES: Model 080A156 Mounting Base (1) Model ICS-2 NIST-traceable single-axis single-point amplitude response calibration at 6000 cpm (100 Hz) OPTIONAL VERSIONS EX- Hazardous Area Approval- contact factory for specific approvals Hazardous Area Approval EEx nL IIC T4, -40°C≤Ta≤121°C, II 3 G Hazardous Area Approval EEx nL IIC T4, -40°C≤Ta≤121°C, II 1 G Hazardous Area Approval Cl I, Div I, Groups A, B, C, D; Cl II, Div I, Groups E, F, G; Cl III, Div I Hazardous Area Approval Cl I, Div 2, Groups A, B, C, D; ExnL IIC T4, AExnA IIC T4 Hazardous Area Approval Exia IIC T4, AExia IIC, T4 M- Metric Mount Supplied Accessory : Model M080A159 Mounting stud, 1/2-20 to M6 x 1 (1) replaces Model 080A156 TO- Temperature Output Temperature Output Range +36 to +250 °F +2 to +121 °C Temperature Scale Factor 5.56 mV/°F + 32 +10 mV/°C Electrical Connector Integral Armored Cable Electrical Connections(Red) Acceleration Output Electrical Connections(Black) Ground Electrical Connections(White) Temperature Output All specifications are at room temperature unless otherwise specified. NOTES: [1] Typical. [2] Conversion Factor 1g = 9.81 m/s². [3] Zero-based, least-squares, straight line method. [4] Measured with mounting stud. [5] 1/4-28 has no equivalent in S.I. units. [6] 1/8" hex Allen key required for English version, 4 mm hex Allen key required for Metric version. [7] Stud torque must exceed sensor hex nut torque to ensure proper dismantling. [8] Stainless steel armor jacket over twisted shielded pair. [9] See PCB Declaration of Conformance PS023 or PS060 for details. [9]
Download Drawing 13444-B.pdf
Download Drawing 18551-NR.pdf
Top